Hey there! As a supplier of SCR Control Systems, I often get asked about how to calibrate these systems. Calibration is super important as it ensures that your SCR Control System works at its best, reducing emissions and improving overall performance. In this blog, I'll walk you through the steps of calibrating an SCR Control System.
Why Calibration Matters
Before we dive into the calibration process, let's talk about why it's so crucial. An SCR (Selective Catalytic Reduction) Control System is designed to reduce nitrogen oxide (NOx) emissions from engines by injecting a precise amount of urea into the exhaust stream. If the system isn't calibrated correctly, it might not inject the right amount of urea. This can lead to higher NOx emissions, which is bad for the environment and can also cause your engine to fail emissions tests. Plus, incorrect calibration can lead to poor fuel efficiency and potential damage to the SCR components.
Pre - Calibration Checks
Before you start the actual calibration, there are a few things you need to check. First, make sure the SCR system is clean. A dirty system can affect the sensors' readings and the overall performance. You can use an SCR Soot Blower to remove any soot or debris that might have accumulated in the system.
Next, inspect all the sensors. The SCR Control System relies on various sensors like NOx sensors, temperature sensors, and pressure sensors. Check if they are properly connected and if there are any signs of damage. A faulty sensor can give inaccurate readings, which will mess up the calibration process.
Also, check the urea tank. Make sure it's filled with the right type of urea solution and that there are no leaks in the urea delivery system. A low urea level or a leak can cause the system to malfunction during calibration.
Step 1: Initial Setup
Once you've completed the pre - calibration checks, it's time to set up the calibration process. You'll need a diagnostic tool that's compatible with your SCR Control System. Most modern systems come with their own proprietary diagnostic software, which you can install on a laptop or a dedicated diagnostic device.
Connect the diagnostic tool to the SCR Control System using the appropriate cable. Make sure the connection is secure. Then, power on the system and wait for it to boot up. The diagnostic tool will communicate with the SCR Control System and display the current settings and readings.
Step 2: Sensor Calibration
The first part of the actual calibration is sensor calibration. Start with the NOx sensors. These sensors measure the amount of nitrogen oxides in the exhaust gas. To calibrate them, you'll need to follow the instructions in the diagnostic software. Usually, it involves taking a baseline reading in a known environment.
For example, you can start the engine and let it run at idle for a few minutes to stabilize the exhaust gas conditions. Then, use the diagnostic tool to record the NOx readings. Compare these readings with the expected values for the given engine operating conditions. If there's a significant difference, the diagnostic tool will guide you through the process of adjusting the sensor settings until the readings match the expected values.
Next, calibrate the temperature sensors. Temperature plays a crucial role in the SCR process as the chemical reaction that reduces NOx works best within a certain temperature range. Use the diagnostic tool to check the temperature readings at different points in the SCR system, such as before and after the catalyst. Again, compare these readings with the known values and adjust the sensor settings if necessary.
Calibrate the pressure sensors as well. These sensors monitor the pressure in the exhaust system and the urea delivery system. Incorrect pressure readings can lead to improper urea injection. Follow the same process as with the other sensors to ensure accurate pressure measurements.
Step 3: Urea Injection Calibration
After sensor calibration, it's time to calibrate the urea injection. The SCR Control System needs to inject the right amount of urea into the exhaust stream to effectively reduce NOx emissions.
First, check the urea injection rate. The diagnostic tool will show you the current injection rate based on the engine's operating conditions. Compare this rate with the recommended values for your specific engine model. If the injection rate is too high or too low, you can adjust it using the diagnostic software.
You may also need to calibrate the urea dosing pump. The dosing pump is responsible for delivering the urea from the tank to the exhaust system. Check its performance by running a test injection. The diagnostic tool will measure the amount of urea injected during the test and compare it with the expected amount. If there's a difference, you can adjust the pump settings to ensure accurate urea delivery.
Step 4: System Testing
Once you've completed the sensor and urea injection calibration, it's time to test the SCR Control System. Start the engine and let it run through different operating conditions, such as idle, low - load, and high - load. Use the diagnostic tool to monitor the NOx emissions, urea injection rate, and other relevant parameters.
Check if the NOx emissions are within the acceptable limits. If they are, it means the calibration was successful. If not, you may need to go back and re - check the sensor and urea injection calibrations.


Step 5: Final Checks
After the system testing, perform some final checks. Inspect all the connections again to make sure they are still secure. Check for any error codes on the diagnostic tool. If there are any error codes, it means there might be a problem with the system that needs to be addressed.
Also, check the urea tank level again. The calibration process might have used some urea, so make sure it's still at an appropriate level.
Conclusion
Calibrating an SCR Control System is a detailed process, but it's essential for the system's proper functioning. By following these steps, you can ensure that your SCR system is calibrated correctly, reducing emissions, improving fuel efficiency, and prolonging the life of your engine.
If you're having any trouble with the calibration process or if you're looking to purchase a new SCR Control System, feel free to reach out. We're here to help you with all your SCR needs. Whether you need an SCR Bypass System or an SCR Silencer, we've got you covered. Contact us for more information and to start a procurement discussion.
References
- SCR System Manufacturer's Manuals
- Industry Standards for Exhaust Emission Control



